Package included:

2*FSESC 4.12

Package included:

2pcs Mini V6 MK5 With Power Button

Warm tips: please do not remove the shrink to protect the pcb electronics components from impurites or metals which result in short circuit or esc burnt damage.

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Advanced Features:

1. Dual ESC can reach 100A big current, give your board strong power
2. One PCBA board integrate two FSESC4.20 ’s function by internal CAN BUS circuit connection.
3. The mater and slave board connection can be switched On/Off
4. Delicate design in details for high quality assurance: add Anti-vibration silicon pad for screw heatsink and  heat-transfer pad
5. Preserve Bluetooth module and RF module connections for both master and slave board
6. Super small size and light weight with heatsink: 79mm*65mm*19mm(L*W*H), wight: 150g

Specs

• Hardware:V4.20
• Firmware:Latest Version
• Current:50A continuous/single, 100A continuous/dual , Instantaneous current 150A per single, total 300A for system instantaneous current.
• Voltage: 8V-60V (Cells: 3-13S LiPo,Safe for 3S to 12S LiPo，Voltage spikes may not exceed 60V! )
• ERPM:60000
• BEC: 5V@1.5A
• BEC type: Internal driver support 
• Modes: DC, BLDC, FOC (sinusoidal)
• Timing: Software calibration 
• Cutoff Voltage: Programmable
• Frequency: PWM input 
• Governor: No
• Programming card: No
• Reverse: Yes
• Motor wire: 12AWG 
• Power cable: 12AWG

 The shipping package contains: 

• 1*Dual FSESC4.20 + Heatsink
• 2*VESC Sensor Wires
• 1*Micro USB 
• 1*Manual

See review 1

See review 2

Function Details:

◆  DRV8302 MOSFET driver / buck converter / current shunt amplifier. 
◆  12pcs NTMFS5C628NL MOSFETs. 
◆  Regenerative braking. 
◆  DC motors are also supported. 
◆  Sensored or sensorless operation. 
◆  Adaptive PWM frequency to get as good ADC measurements as possible.
◆  Good startup torque in both sensored and sensorless mode. 
◆  Duty‐cycle control, speed control or current control. 
◆  Wireless WII nunchuk (Nyko Kama) control through the I2C port. This is  convenient for electric skateboards. 
◆  Optional PPM signal output. e.g.  when controlling an RC car from a  Rasp Berry Pi or an android device. 
◆  The USB port uses the modem profile, so an Android device can be   connected to the ESC without rooting. Because of the servo output, the odometry and the extra ADC inputs(that can be used for sensors),  this is perfect for modifying an RC car to be controlled from Android  (or Raspberry Pi). 
◆  Sensored and sensorless (FOC) Field Oriented Control allows your electric skateboard to run with barely any motor noise, it auto-detects motor parameter since FW3.34. 
◆  Many safety features such as current control and temperature control features. 
◆  The motor is used as a tachometer, which is good for odometry on modified RC cars. 
◆ Adjustable protection against: 
Low input voltage 
High input voltage 
High motor current 
High input current 
High regenerative braking current (separate limits for the motor 
and the input) 
Rapid duty cycle changes (ramping) 
High RPM (separate limits for each direction). 
◆ When the current limits are triggered, a soft back-off strategy is used while the motor keeps running. If the current becomes too high, the motor is switched off completely. 
◆ The RPM limit also has a soft back-off strategy. 
◆ Commutation works perfectly even when the speed of the motor changes. This is due to the fact that the magnetic flux is integrated after the zero crossing instead of adding a delay based on the previous speed.
◆ When the motor is rotating while the controller is off, the commutations and the direction are tracked. The duty-cycle to get the same speed is also calculated. This is to get a smooth start when the motor is already spinning

Manual download：Dual_FSESC4.20_100A_MANUAL_20181106.pdf.pdf

Programming Reference Tutorial 1.16

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

please do not remove the shrink to protect the pcb electronics components from impurites or metals which result in short circuit or esc burnt damage.

Dual FSESC4.20 Plus(Pro Switch) base on VESC, it’s upgraded on

Dual FSESC4.20 100A (Based on VESC ) with Anodized Aluminum Heatsink

Upgraded Features:

1. Integrated anti-spark switch function in the PCBA 

     2. More thinner for compact in case
               With heatsink: 64 x84x20.5mm(Include Heatsink)

Specs:

• Hardware:V4.20
• ERPM:60000
• Firmware:Latest firmware version
• Current:50A continuous/single, 100A continuous/dual ,burst 150A/single, burst 300A/dual
• Voltage: 8V-60V (Cells: 3-13S LiPo,Safe for 3S to 12S LiPo，Voltage spikes may not exceed 60V! )
• BEC: 5V@1.5A
• BEC type: Internal driver support 
• Modes: DC, BLDC, FOC (sinusoidal)
• Timing: Software calibration 
• Cutoff Voltage: Programmable
• Frequency: PWM input 
• Programming card: No
• Reverse: Yes
• Regenerative braking power: Yes
• Motor wire:12AWG
• Power cable:12AWG

 The shipping package contains: 

• 1*Dual FSESC4.20 Plus + Heatsink
• 2*VESC Sensor Wires
• 1*Micro USB 
• 1*Manual 
• 1*16mm LED button

Manual:

Dual FSESC4.20 PLUS MANUAL

Design In Details

Diagram

What's the main difference between Dual FSESC4.20 SMART  and Dual FSESC4.20 Plus?

Programming Reference Tutorial 1.16

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Dual FSESC6.6 Plus(Pro swtich) based on Dual FSESC6.6 

Warm tips: please do not remove the shrink to protect the pcb electronics components from impurites or metals which result in short circuit or esc burnt damage.

Upgraded features:

• Pro switch version:
• Power on/off by pressing the button
• Added Can bus connector, be more convenient for 4WD set up
• Changed the USB port soldering process to SMT soldering instead of manual soldering
• Changed the big capacitors to SMT mounting capacitors ,and add more mosfets in the bottom side.

Spec:

- Hardware: V 6.7

- Firmware: Latest firmware version

- Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC

- Voltage spikes may not exceed 60V

- Current: Continuous 100A single, total 200A ,  Instantaneous current 400A per single, total 800A for system instantaneous current. values depend on the mounting  and ambient temperature around the device!

- 5V 1.5A output for external electronics for single

- 3.3V 1A output for external electronics for single

- Modes: DC, BLDC, FOC (sinusoidal)

- Supported sensors: ABI, HALL, AS5047

-ERPM:150000

-Size: 81x77x20mm including heatsink 

-Motor wire: 12AWG

-Power cable:8AWG

-Recommend bullet connectors: 4MM Bullet Connector 

          -Reminder: Detected battery voltage tolerance: +/-0.6V 

The shipping package contains:

• 1*Dual FSESC6.7+Heatsink
• 2*VESC Sensor Wires
• 1*LED button 
• 1*Micro USB
• 1*Manual

Other detail spec is the same with Dual FSESC6.6(big size version, without switch), you can get more information by here:

https://flipsky.net/collections/electronic-products/products/fs-esc-6-6

Dual FSESC6.7 Wiring Diagram:

Set Up diagram

Set up for 4WD 

DUAL FSESC6.7 PLUS SIZE:

Programming Tutorial Reference (VESC tool 1.16)

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Please be careful to limit the Absolute Maximum Current below 250A,setting page

Specs:

• Dual 75100 Size:L107mm*W103mm*H18.5mm
• Voltage:14-84V (4-20S safe)
• Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting  and ambient temperature around the device!
• BEC:5V@1A
• Support BLDC square wave mode control and FOC sine wave mode
• Firmware: latest (firmware update supported)
• ERPM:150000
• Control Interface Ports:USB,CAN,UART
• Supported Sensors:ABI，HALL，AS5047，AS5048A
• Input Set Support:PPM，ADC，NRF,UART
• Wire Size: 12AWG
• Phase filter: No
• Programmable: Yes
• Regenerative Capacity: Yes

Warm tips:

Detail:

flipsky_esc_tool  software and manual download link

Note: USB cable black or white will be shipped randomly.

Specifications : 

• Firmware: V1.2 (firmware update via Flipsky ESC Tool supported)
• Voltage: 14-84V (safe for 4S-20S)
• Continuous Current: 100A / Single; 200A / Dual (values depend on the mounting  and ambient temperature around the device!)
• Peak Current: 250A / Single; 500A / Dual
• Communication Ports: USB, CAN, UART, PPM, ADC
• Input Signals Support: PPM, ADC, UART (compatible with FLIPSKY remote VX4 and VX3Pro only at present)
• Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored)
• BEC: 5V@1A
• Multiple Speed Gear levels: Low, Medium, High, Reverse
• Front Lights, Rear Brake Lights & Horn: Support
• Programmable: Yes
• Regenerative Capacity: Yes
• Slide Poweron & Auto shutdown: Yes
• Self-resetting switch with green LED button Diameter: 16mm
• Power Wire Size: 10AWG; Motor Wire Size: 12 AWG
• Size: L132*W81*H26.5mm(Including Alu. Case)

Features:

1.Adopting CPU AT32F403ARCT7 with the structure of ARM Cortex-M4 allows CPU clock speed.
2.240MHz and the max PWM switching frequency 45KHz improves the motor RPM.
3.Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different battery voltages and many control ways.
4.Programmable via Flipsky remote controller VX4 (remote firmware version: VX4_V1.2.1 or above).
5.Supporting motor FOC with low working noise and smooth starting.
6.Supporting Real-time data and fault alerts.
7.Supporting adaptive variable PWM frequency control.
8.Supporting sensor mode(HALL) and sensorless mode(IPDS, HFPI).
9.Supporting control types: Current, Duty Cycle
10.Protection functions: low and high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature and over current protection, battery over discharge protecting, motor over-temperature protection.
11.Integrated smart switch function: supports sliding poweron and automatic shutdown function; automatic shutdown time is adjustable via ESC TOOL.
12.Supporting extra interface like front lights, rear brake lights and horn fixtures.

Wiring diagram:

Specs:

• Type: Charge only
• Cell Chemistry: Li-ion (3.7V nominal)
• Balance method: Passive balance
• 4S-24S Series Count: 4-24S
• Charge Current: 20A
• Overcharge Voltage: 4.25V
• Overcharge Reset: 4.19V
• Balance: @4.2V
• Overtemperature: 60°C
• Overtemperature Reset: 40°C
• Size: 110*30*11mm
• Net weight: 30g

Features:

1. Compact charge only design
2. Cell balance indicator LED
3. Compatible with 4s-24s battery
4. Designed to be ultra-compact and simple to use without any configuration required
5. Anodized aluminum heatsinkcase, stable performance.

Functions:

1. Balance function
2. Overcharge protection
3. Overtemperature protection
4. Cell balance indicator LED

Operation Notes:

1. Please ensure the correctness of the wiring sequence, from B0-B12, B13-B24, the voltage increases from low to high in sequence.
2. This BMS is compatible with battery packs up to 24s, which is over 100V DC when fully charged. Electric shocks from high voltage may cause serious injury.Please pay attention to safety when using.
3. This device is designed to reduce the risk of charging and will not protect against overcurrent discharge, undervoltage, internal pack shorts, pack overtemperature

Please use 5V/2A charger for VX1 (Max. Input voltage of 6.5VDC for VX1). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 remote controller may be damaged.

Features

• 2.4Ghz band width
• Support 3 speed modes
• Support cruise control mode
• Remote and E-skateboard power indication lights
• Support checking remote battery volume
• Comfort touch: ABS+Rubber painting surface
• Rechargeable Li-ion Battery
• Wrist strap
• VX1 Remote comes with Receiver 

Function Show

Kindly Reminder !

1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned. 

2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one. 

3. When you choose UART mode connection for VX1 remote receiver, pls do connection after your programming in VESC tool. Or else , it will influence programming. And In UART mode, there is no need to do adjust for remote. 

Receiver Connection Diagram

For Single V4

For Dual FSESC4.20: Both hook up with bluetooth and remote receiver

For Single V6

For Dual FSESC6.6 Plus : both hook up with bluetooth and remote receiver

For PPM mode(or Non VESC )

Manual：VX1_Remote_VX1_product_manual_-20190316.pdf

Please use 5V/2A charger for VX2 (Max. Input voltage of 6.5VDC for VX2). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX2 remote controller may be damaged.

Features:

• Color screen
• Option choice for km/h and miles/h
• Option choice for FSESC and other VESC( FOCBOX)
• 2.4Ghz band width
• Real time data reading and 0.95OLED display
• Support 3 speed modes
• Support cruise control mode
• Remote and E-skateboard power indication lights
• Rechargeable Li-ion Battery
• Wrist strap
• Battery last for 12 working hours
• VX2 Remote comes with Receiver

Receiver Connection Diagram

For Dual FSESC6.6 Big size :

For Dual FSESC4.20 :

Remark:

2.The Flipsky VX2 remote just can compatible with base on vesc , if your VESC has changed the program, please choose to purchase carefully.

Function Show

Feature:

• 1.6-inch super clear and big screen display
• Display shows more: Except for basic telemetry data, it also display GPS, motor power, real-time temperature of MOS tube, and throttle progress bar information
• Be compatible with Flipsky FSESC and other VESC and Non-VESC
• ESK8 mode / E-surf mode switching freely
• Esurf mode：Cruise speed control function
• Waterproof IP rating: IP67
• Bigger remote battery capacity:1500MA
• ESC failure report ：Detect possible failures of the ESC in time for replacing
• Controller mode: PPM/UART 
• Charging way:Wireless Magnetic Charging
• VX3 Remote comes with Receiver

Wiring Diagram:

Reference video:

Spec:

• Hardware: V1.0
• Max voltage: 20S (90V，safe for 80V)
• Continuous Current: 80A .
• Max Current: 200A((It is better to increase bigger heat sink)
• Burst current 1000A(theoretical current)
• LED button diameter:12mm
• Size:68mm*34mm*9.5mm(10AWG Wire)

Aluminum pcb Features:

• MOS fets: use 10*10 large package MOS , with better overcurrent and heat dissipation performance
• Control mode: lock key control switch mode; press the lock button to lock it to open, and the LED light will light up at the same time, press the lock button again to bounce it to turn off, and the LED light turn off at the same time.
• The function of the product: the aluminum substrate fire-proof spark switch efficiently and safely protects the power contacts from being burnt and oxidized by the electric spark, effectively protecting the electronic components of the integrated circuit from breakdown and damage, preventing the occurrence of electric sparks that may cause an explosion, and more effectively extending the electronics Product life.
• Aluminum base plate has better heat dissipation performance. It is more convenient to add a larger heat sink for continuous large current output. The heat sink and the heat sink are connected with thermally conductive silicone grease, which has a better heat conduction effect.

Warnings:

• Do not peel off the heat shrink.There’s no screw to lock the heatsink and PCBA, Only the heat-transfer silicon pad is naturally sticky to heatsink and PCBA.
• No short circuit protection, DO NOT short circuit output!
• No reverse polarity protection. DO NOT plug in backwards.
• Recommended to keep output capacitance under 6,000 uF. Proper operation cannot be guaranteed at higher capacitances.
• Do not Hot-Swap. Try to make sure everything is off before connecting and removing. If need be, unplug from battery first, wait for ESCs to turn off, then unplug ESCs. Do the reverse for plugging in, plug in ESCs first before plugging the switch into the battery.
• Engineers have thoroughly tested prototypes; however, this is still a new design and a first production run, please exercise extreme caution (as one would normally do with any electric vehicle) when using this device.
• Do not attempt to reprogram the MCU unless otherwise advised. Doing so will void any warranty and also put the switch at great risk of failure.

 Wiring diagram：

The Group D8 package includes:

1* Dual FSESC6.7 Pro Plus With Heat Sink

2* Battle Hardened 6384 Motor 190KV With Pulley(Random send out 8mm16T OR 15T motor pulley)

1*Screen Remote VX2 Pro

2*Motor Keyway

2* Sensor Wire

1*USB cable

The Group D7 package includes:

1*Dual FSESC6.7 Pro Plus  With heat sink

2*Battle hardened 6374 motor with pulley

1*VX2 Remote Controller

2* Sensor Wire

1*USB cable

The motor detail:

Flipsky battle hardened 6374 Motor

Flipsky battle hardened 6384 Motor

Flipsky battle hardened 63100 Motor

All Terrain Tire :

• Material:Pneumatic tire
• Tire Size: 200mm / 8''
• Tire Width: 50mm / 2''
• The wheels are pneumatic tires(with inner tube), the tires are inflated with air

 Truck: 

• Truck Length: 420mm / 16.5''
• Axle Length: 60MM / 2.4''
• Axle Diameter: 10MM

Others: 

• Hub material: Aluminium Alloy
• Tyre Material: Rubber
• Axle Hole Size:10 mm
• Tyre Pressure: 60PSI  410kpa
• HUB Axle Diameter: 10 mm
• HUB Teeth: 72 teeth 
• Belt:445mm
• Pulley Diameter: 113 mm  
• Pulley Width: 18 mm  HTD 5M
• Gear ratio ：72:15

Package included:

Shipping method：

By DHL/Fedex :around 5-9 working days

By train / sea :around 30-39 days

Detail Size:

The Group D9 package includes:

1*Dual FSESC4.20 100A 

2*Battle hardened BLDC Belt Motor 6354 2450W With Pulley(Random send out 16T OR 15T motor pulley)

1*2.4Ghz Remote VX1 for DIY electric skateboard

1*Anti spark Switch Smart Enhanced 200A 

1*Bluetooth Module

2* Sensor Wire

1*USB cable

The Group D10 package includes:

1*Dual FSESC6.7 MINI SIZE

2*Battle Hardened 6374 motor With Pulley( Random send out 16T OR 15T motor pulley)

1*Screen Remote VX2 Pro

1*Anti spark Switch Smart Enhanced 200A 

2* Sensor Wire

1*USB Cable

Battle Hardened 6374 motor

The Group W7 Water Sports Kit Includes:

1*Flipsky FSESC 75300 84V

1*FS65161 12MM Shaft 

1*VX3 Waterproof Remote controller

1*Propeller

The reference video:

The Group T7 DIY Electric Skateboard Full Truck and Motor Kits Includes:

1*15.22”Double Kingpin Trucks (front and back truck)

1*Motor Mount(pairs)

4*175MM Wheels/200MM Wheels

2*355mm Belt

2*Flipsky Battle hardened 6374/6384/63100 Motors

2*Shaft sleeve

Reference video:

Group T5 DIY Electric Skateboard Double Kingpin Trucks and Motor Kits (Dual Drive)

1*12"Double Kingpin Trucks（front and back truck)

1*motor mount mount (pairs)For 12" kingpin trucks 63 series random option

1*Honeycomb Wheels（included 4wheels and two 335mm belts）

2*Flipsky Battle Hardened 6354 or 6374 Motor With Pulley( 10mmD-shaft motors-99mm length)

The Group S11 package includes:

1* FSESC 6.7 Pro (D:FSESC6.7+Heat Sink+Button)

1* Battle hardened  Motor 6374 140KV / 190KV 3250W With pulley

1*2.4Ghz Remote VX1 for DIY electric skateboard

1*Bluetooth Module for v6

1* Sensor Wire

1*USB cable

Cost-Effective Group S3 Package includes:

1*Standard FSESC4.12 50A

1* Battle hardened 6354 motor 

1*VX1 Remote Controller

1*Anti-spark Swithc Pro 280A V3.0 With Heatsink

1*Bluetooth Module for V4

1*Sensor Wire

1*USB cable